Hamilton Beach Iron 840066300 User Manual

Use & Care for Irons..........................2  
USA: 1-800-851-8900  
840066300  
 
Parts and Features  
1. Spray/Blast  
2. Adjustable Steam Switch  
3. Water Tank Opening  
4. Spray Nozzle  
5. Water Window  
6. Temperature Control Dial  
7. Sole Plate  
8. Automatic Shutoff  
Reset Button and  
Power On Light  
9. Heel Rest  
10. Cord  
To Dry Iron  
1. Plug in iron.  
2. Set the Adjustable Steam Switch  
3. Turn Temperature Control Dial to  
desired  
temperature.  
to 0 (the Dry  
Iron position).  
Allow 3 minutes  
for iron to  
reach desired  
temperature.  
4. To turn iron OFF, turn Temperature  
Control Dial to O. Unplug iron.  
3
 
To Steam Iron  
1. Unplug iron. Using a cup, slowly  
pour 5 ounces  
4. Allow 3 minutes for the iron to reach  
desired temperature.  
5. To turn iron off, turn Adjustable  
Steam Switch to 0 (Dry Iron). Turn  
the Temperature Control Dial to O  
(OFF). Unplug iron.  
Opening  
of tap water  
into water  
tank opening  
as illustrated.  
6. Empty water from the iron following  
directions in “Caring for Your Iron.”  
Water  
2. Plug in iron.  
Please use ordinary tap water. If you  
have extremely hard water, alternate  
between tap water and distilled water  
for use in the iron.  
3. Set the Adjustable Steam Switch to  
desired amount  
of steam. Turn  
the Temperature  
Control Dial to  
desired setting  
in the steam  
range.  
Features (on selected models)  
Automatic Shutoff Reset Button –  
After the iron has  
Adjustable Steam Switch – Set the  
switch at 0 to dry  
been on for 1 hour,  
the orange light  
will go out and the  
iron will automati-  
iron. Move switch  
to  
steam or  
when using blast.  
cally turn off. To  
Reset  
Button  
continue ironing,  
push the Reset  
Button again and  
the iron will reset  
for 1 hour.  
Spray/Steam Selector – Turn knob to  
select Spray or  
Steam. On Spray,  
push to release a  
fine spray of water  
for difficult wrinkles  
in cotton or linen.  
On Steam, push  
Power Light – This red light indicates  
the iron is  
plugged in.  
for an extra blast  
of steam.  
Power  
Light  
Wrap & Snap Cord – When finished  
ironing, let the iron cool then wrap cord  
and secure with the Wrap & Snap on  
the plug.  
4
 
Fabric Setting Chart  
Steam Setting  
To Iron  
Ironing Instructions  
Off/O  
Nylon  
Silk  
Dry iron on the wrong side of the fabric.  
Dry iron on the wrong side of the fabric.  
Steam iron on the wrong side of fabric.  
Iron with fabric still damp.  
Wool  
Polyester  
Rayon  
Cotton  
Linen  
Iron on the wrong side of fabric.  
Iron while still damp using steam and/or spray.  
Iron on wrong side of fabric while still damp.  
Troubleshooting  
PROBLEM  
THINGS TO CHECK  
Iron won’t heat.  
• Is the iron plugged in and the outlet working? Check  
the outlet by plugging in a lamp.  
• Is the Temperature Control Dial turned to a  
fabric setting?  
• If auto shutoff model, is the Reset Button light  
illuminated? If not, push to reset.  
Water is leaking  
out of the iron.  
• Do not overfill the water tank.  
• If steam ironing, is Adjustable Steam Dial in a steam  
position, the Temperature Control Dial in the steam  
range, and did the iron have enough time to preheat?  
• If dry ironing, make sure the Adjustable Steam Dial is  
in the DRY IRON position.  
Iron won’t steam.  
• Check the water level.  
• Is the Adjustable Steam Dial in the STEAM position?  
• Has the iron had enough time to preheat?  
Iron leaves spots  
on clothing.  
• ALWAYS empty the water tank of the iron after using.  
Water left in the tank may discolor clothing and  
soleplate.  
Wrinkles not  
removed.  
• Check Temperature Control Dial is set to correct fabric.  
Iron too hot.  
• Check Temperature Control Dial and set to lower  
setting. Let iron cool down 5 minutes before continuing.  
5
 
Caring for Your Iron  
Iron  
Soleplate  
1. The Water Tank of your iron should  
be emptied after each use. Turn  
Temperature Control Dial to O.  
Unplug the iron and hold over a  
sink. Slowly tilt pointed end of iron  
down over sink. Water will run out  
of water tank opening.  
1. Never iron over zippers, pins, metal  
rivets, or snaps, as these may  
scratch the soleplate.  
2. To clean occasional build-up on the  
soleplate, wipe with a sudsy cloth.  
Do not use abrasive cleansers or  
metal scouring pads.  
2. After iron has completely cooled,  
wrap cord loosely around the iron  
and store in an upright position. Do  
not store iron laying flat on soleplate.  
3. Always store iron upright in the heel  
rest position.  
Customer Service  
If you have a question about your iron, call our toll-free customer service number.  
Before calling, please note the model, type, and series numbers and fill in that  
information below. These numbers can be found on the bottom of your iron. This  
information will help us answer your question much more quickly.  
MODEL: ______________ TYPE: _______________ SERIES: _________________  
TWO YEAR LIMITED WARRANTY  
Hamilton Beach/Proctor-Silex, Inc. warrants this appliance to be free from defects in  
material and workmanship for a period of two (2) years from the date of original purchase,  
except as noted. There is no warranty with respect to the following, which may be supplied  
with this appliance: glass parts, glass containers, cutter/strainer, blades and/or agitators.  
This warranty extends only to the original consumer purchaser and does not cover damage  
from abuse, neglect, use for commercial purposes, or any other use not found in the print-  
ed directions. HAMILTON BEACH/PROCTOR-SILEX, INC. EXPRESSLY DISCLAIMS ALL  
RESPONSIBILITY FOR CONSEQUENTIAL DAMAGES OR INCIDENTAL LOSSES CAUSED  
BY USE OF THIS APPLIANCE. Some states or provinces do not allow this exclusion or limita-  
tion of incidental or consequential losses, so the foregoing disclaimer may not apply to  
you. If you have a claim under this warranty, DO NOT RETURN THE APPLIANCE TO THE  
STORE! Please call our CUSTOMER SERVICE NUMBER. (For faster service please have  
model, series, and type numbers ready for operator to assist you.)  
CUSTOMER SERVICE NUMBERS  
In the U.S. 1-800-851-8900  
In Canada 1-800-267-2826  
KEEP THESE NUMBERS FOR FUTURE REFERENCE!  
This warranty gives you specific legal rights, and you may also have other legal rights  
which vary from state to state, or province to province.  
HAMILTON BEACH PROCTOR-SILEX,INC.  
Washington, North Carolina 27889  
PROCTOR-SILEX CANADA,INC.  
Picton, Ontario K0K 2T0  
840066300  
12/99  
6
 

Graco Swing Sets 1522 User Manual
Grizzly Drill G7945 46 User Manual
Haier Washer HWMP95TL User Manual
Honeywell Weather Radio TC682EL User Manual
HP Hewlett Packard Computer Accessories ProLiant BL495c G6 User Manual
HP Hewlett Packard Personal Computer D8C26UTABA User Manual
Huawei Recording Equipment MG323 User Manual
Husqvarna Edger 323E User Manual
Husqvarna Lawn Mower 46S User Manual
Hypertec Carrying Case TANCD2HY User Manual