33⁄16" PORTABLE PLANER
MODEL G9003
INSTRUCTION MANUAL
COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
APRIL, 2000 PRINTED IN U.S.A.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP ALL SAFETY DEVICES IN
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept a safe distance from
work area.
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power
tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.
-3-
G9003 Portable Planer
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD
13. DON’T OVERREACH. Keep prop-
for the tool. Make sure your exten-
sion cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
er footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNIN-
TENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
Minimum Gauge for Extension Cords
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
7-10
16
16
12
12
11-12
13-16
17-20
21-30
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
19. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER
OFF. Don’t leave tool until it comes
to a complete stop.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
-4-
G9003 Portable Planer
Safety Instructions For Portable Planers
5. DO NOT REMOVE EXCESSIVE
AMOUNTS OF WOOD IN A SINGLE
PASS. Better results can be
achieved by taking multiple passes
with a small amount of material
removal in each pass.
1. USE ONLY FOR WOOD. This
machine is not designed to process
any material other than wood.
2. ALWAYS KEEP FINGERS AND
HANDS AWAY FROM ROTATING
CUTTERHEAD. Never attempt to
clear chips away from the base of
the chip chute when the machine is
running. Stop the machine, unplug
it, then clear away the debris.
6. INSPECT STOCK THOROUGHLY
BEFORE PLANING. Look stock
over for any grit, sand, nails, staples
or other foreign materials before per-
forming planing operations. Foreign
materials can damage the blade and
can throw off debris which may
cause injury.
3. NEVER OPERATE WITH DULL
OR DAMAGED BLADES. Check
blades frequently for sharpness or
damage. Damaged or dull blades
put excessive strain on the machine
and can cause loss of control of the
unit.
7. MAKE SURE WORKPIECE IS
SECURELY CLAMPED OR OTH-
ERWISE HELD IN PLACE. Also
make sure the clamps will not
obstruct the movement of the Planer
as it progresses through the cut.
Hitting an unexpected obstruction
can cause potential loss of control of
the machine.
4. ENSURE PLANER IS PROPERLY
ADJUSTED BEFORE STARTING.
Always use a test piece to check the
adjustment and operation before
starting on the actual workpiece.
-5-
G9003 Portable Planer
CONTROL LOCATION
Control Location
Specifications
Speed: 15000 RPM
Refer to Figure 1 for the location of the key
components and controls of this Planer.
Become familiar with the controls and the
adjustments before operating the Planer.
Motor Type: Universal Brush Motor
Motor Power: 1⁄2 HP, 110V, 5.0 Amp
Cutterhead: 2 Blades
Maximum Cutting Width: 33⁄16"
Maximum Stock Removal/Pass: 1⁄32"
Maximum Rabbet Depth: 11⁄32"
Weight: 5.75 lbs
Accessories Included: Fence, Blade
Removal Wrench, Sharpening Jig, Blade
Setting Jig,
Replacement Belt and
Replacement Motor Brushes
ON/OFF Trigger
Trigger Lock
Depth
Adjustment Knob
Fence
Lock
Power Cord
Rear Foot
Belt Cover
Front
Foot
Fence
Fig 1. Location of controls.
-6-
G9003 Portable Planer
BLADE ADJUSTMENT & REMOVAL
the amount of contact is the same
all the way across.
3. If there is too much contact, or
none at all, at any point across the
blade, then the blade needs to be
reset. Refer to Blade Installation
Section.
Turn the switch off and unplug the
Planer from power before attempting
blade removal or any adjustments.
Serious injury may occur if the unit
should be accidentally started while
checking or removing the blades.
4. Repeat procedure for the other
Blade.
The Planer comes with the blades already
installed. Check the blades before the first
use to make sure they are set properly.
To Remove the Blade Assemblies:
1. Using the belt pulley, rotate the
Cutterhead so that one of the two
Blade Holders is positioned in the
opening in the base.
To Check Blade Height Setting:
1. Lay a straightedge across the
Rear Foot and the Cutterhead. Do
not position the straightedge so it
contacts the Front Foot. See
Figure 2.
2. Use the supplied T-handle wrench
to remove the three hex head bolts
holding the Blade Assemblies to
the
Cutterhead.
Hold
the
Cutterhead in position with the Belt
Pulley. See Figure 3.
Figure 2. Checking Blade height.
Figure 3. Removing Blade Holder bolts.
2. Rotate the Cutterhead manually
with the exposed portion of the belt
(right next to the Cutterhead). The
tip of the blade at its highest point
should just barely touch the
straightedge. Move the straight-
edge back and forth across the
width of the blade to make sure
3. Lift the Blade Holder and Blade
Assembly off, being careful to not
come in contact with the sharp
edge of the blade.
4. Repeat procedure for the other
Blade.
G9003 Portable Planer
-7-
BLADE INSTALLATION
4. Set
the
Blade/Back
Plate
Assembly onto the Cutterhead.
Make sure the bottom edge of the
Back Plate is positioned into the
slot on the Cutterhead. See
Figure 5.
Turn the switch off and unplug the
Planer from power before attempting
blade installation or any adjustments.
Serious injury may occur if the unit
should be accidentally started while
installing the blade.
Make certain edge of back plate
engages in slot in cutterhead
The Blade must be mounted to the Back
Plate using the Blade Setting Jig. Using
this jig controls how far the blade extends
from the Cutterhead once it is installed.
1. Place the Blade onto the Setting
Jig.
2. Lay the Back Plate onto the top of
the Blade, pushing it up firmly
against the edge of the Jig. See
Figure 4.
Fig 5. Inserting blade assembly on
Cutterhead (Rear Foot removed for clarity).
Blade flush to this edge
5. Set the Blade Holder over the
Blade Assembly so the notches in
the side of the Holder engage the
rear edge of the blade. Install three
hex head bolts and washers, and
tighten with the supplied T-handle
wrench.
6. Repeat the procedure for the other
blade.
Back Plate flush to this edge
Fig 4. Blade in position on Setting Jig.
Never operate the Planer with only
one blade installed. This will cause
an imbalance of the rotating cutter-
head and may allow the Planer to go
out of control, possibly causing
injury.
3. Install two Phillips® head screws
with washer and lockwasher
through the slots on the Back
Plate into the Blade. Tighten
securely.
-8-
G9003 Portable Planer
BLADE SHARPENING
The Blade must be completely removed
from the Planer and from the Back Plate in
order for it to be safely sharpened. Follow
the preceding instructions for Blade
Removal.
For the best results, have planer blades
sharpened by a professional sharpening
service which has the grinding and mea-
surement equipment to assure that the
blade cutting geometry is maintained at
optimum levels. It is a procedure which
requires special equipment and precision,
otherwise, a set of blades can be easily
ruined. Knives should always be ground as
a set so that an equal amount of material is
removed which will maintain the balance of
the cutterhead.
Fig 6. Blades in Sharpening Jig.
3. The bevel edge of the blades will
extend beyond the sloped edge of
the Jig. The blades can be sharp-
ened by sweeping a fine metal file
along the two edges, using the
existing bevel angle as a guide. Or
the entire Jig can be turned face
down on a sharpening stone and
swept across the surface of the
stone.
The blades can be tuned up between
major sharpenings using the Sharpening
Jig supplied. Remove both Blades com-
pletely from the Planer.
4. Remove the Blades from the Jig
and reinstall into the Planer.
To Sharpen Blades:
Blade sharpness is one of the most impor-
tant factors in getting good results with the
planer. Take care to ensure that the work-
piece being planed is free from grit, dirt, or
nails or other embedded metals such as
staples. These can nick or chip the knives
and can require a complete regrinding.
1. Separate the Blade from the Back
Plate by removing two Phillips®
head screws.
2. Mount the two Blades onto the
Sharpening Jig as shown in
Figure 6.
Planer blades are dangerously sharp.
Use extreme caution when inspecting,
removing, sharpening, or replacing
blades into the cutterhead. Substantial
risk of laceration injury exists!
-9-
G9003 Portable Planer
OPERATIONS
3. Turn the Planer on by pulling the
Setting Cutting Depth
ON/OFF trigger. Allow the cutter-
head to achieve full speed before
engaging the workpiece.
Lay a straightedge across the Rear Foot
and extend it across the Front Foot. Rotate
the cutterhead so neither of the blades are
touching the straightedge. Turn the Depth
Adjustment Knob until the Front and Rear
plates are at the same height (the straight-
edge will contact both feet evenly). This is
a “0” depth of cut. Note the position of the
“0” point on the knob scale. Three-quarters
of a full rotation of the knob is equivalent to
4. Once the cutting begins, push the
Planer firmly across the workpiece
at the same rate of speed. Do not
stop the Planer’s progress across
the piece during the pass. Do not
apply downward pressure, use the
handle to apply force to push the
Planer along.
1
5. Check the edge for straightness
and squareness, or for the desired
profile, as successive passes are
made.
a ⁄32" depth of cut, the maximum depth of
cut recommended. Generally the best
results will be achieved with several
successive passes rather than trying to remove
the maximum amount of material in one pass.
Planing
Operating this equipment has the
potential to propel debris into the air
which can cause eye injury. Always
wear safety glasses or goggles when
operating equipment. Be certain the
safety glasses you wear meet the
appropriate standards of the
The most common operation is to plane
the edge of a board to get a straight,
square edge. A Portable Planer is also
useful when an uneven edge is required,
such as when fitting a countertop to a wall.
The Planer can be used to cut right down
to a scribe line by taking selective cuts.
American
National
Standards
Institute (ANSI).
This Planer can also be used for face plan-
ing, that is, to clean up the rough surface of
a board. This is most easily accomplished
on boards which are less than 33⁄16" wide
where the planing can be done in a single
pass. Success in face planing will be best
when very light passes are made.
To Perform Planing Operations:
1. Secure the workpiece firmly with
clamps so it will not move during
the planing process.
2. Set the desired depth of cut.
-10-
G9003 Portable Planer
OPERATIONS
successive passes to achieve the full
Chamfering
depth of the rabbet as the maximum depth
1
of cut is ⁄32" per pass. The maximum rab-
The Front Foot has a V-groove machined
into it to allow for edge chamfering.
Position the Planer on the corner of the
workpiece, with the V-groove seated on
the corner. See Figure 7. Be sure the
workpiece is firmly secured with clamps or
other holding devices.
bet depth is 11⁄32". See Figure 8.
To Perform Rabbeting Operations:
1. Secure the workpiece firmly with
clamps to eliminate movement
during the planing operation.
2. Install the fence guide by inserting
it into the hole in the left front of
the planer body and tightening the
holding knob at the front of the
planer.
Start the Planer and let it get to full speed
before moving the Cutterhead into the
workpiece. Apply steady, even pressure
and keep the Planer moving along the
edge. The Rear Foot will sit on the
Chamfered edge as it comes out of the cut-
ter. Support the Planer so it does not slip
off of the edge.
3. Set the fence distance so that the
cutter cuts into the workpiece by
the desired width. Test on a sam-
ple piece and check dimension.
4. Set the desired depth of cut with
the Adjustment Knob. Generally it
is best to take shallow cuts per
pass to avoid chipping.
5. Start the Planer. Let the cutter-
head get up to full speed before
engaging the cutter into the work.
6. Take successive passes until the
full depth is achieved.
Fig 7. Cutting a chamfer.
Rabbeting
Rabbeting is the cutting of a notch along
the edge of a board to allow mating pieces
to fit together tightly. The Planer can be
used to cut rabbets by using the supplied
fence and setting it so that only the neces-
sary amount of the cutterhead will actually
cut into the workpiece. It will take several
Fig 8. Cutting a rabbet.
-11-
G9003 Portable Planer
MAINTENANCE
Maintenance
Brush Replacement
The universal motor has two brushes
which may periodically need replacement.
When checking or replacing the brushes,
make sure the slots the brushes fit into are
clear of grit or debris so the brushes are
free to move in and out.
Your 110 V Portable Planer will give you
hundreds of hours of operation time before
ever needing service. This product is dou-
ble insulated which provides protection
from electrical shock should a problem
ever develop with grounding. Great care
must be taken whenever servicing double
insulated equipment to make certain the
repair does not destroy the insulated prop-
erties. Service should be performed only
by a qualified electrical technician.
To Replace The Brushes:
1. Remove the motor cover by remov-
ing the two screws on the housing.
2. Remove the brush caps with a large
flat bladed screwdriver. See Figure
10.
Belt Replacement
3. Pull the brush out. The end has a
metal disc which is attached to a
spring-like piece. If the slot has for-
eign material in it, the brush may be
hard to remove.
Refer to the Troubleshooting guide for typ-
ical symptoms of a worn belt.
To Replace the Belt:
1. Remove the belt cover.
2. Remove broken or worn belt.
4. Clear the brush slot with a screw-
driver and make sure it is free of grit.
Insert the new brush, check to make
sure it goes into the slot and comes
out against the commutator.
3. Work the new belt onto the pul-
leys. It will be necessary to push
down on the edge of the belt while
manually turning the pulleys. See
Figure 9.
5. Replace the brush cover.
6. Repeat for the other brush.
7. Replace the motor cover.
4. Replace the belt cover.
Fig 10. Replacing motor brushes.
Fig 9. Replacing belt.
-12-
G9003 Portable Planer
OPERATING TIPS
Operating Guides and Tips
Operating this equipment has the
potential to propel debris into the air
which can cause eye injury. Always
wear safety glasses or goggles when
operating equipment. Be certain the
safety glasses you wear meet the
appropriate standards of the
Avoid overloading the planer. Do not
apply downward pressure to the tool
while using. Do not feed into the
work so rapidly that it causes the
motor to bog down.
Ensure the safety of the workplace.
Clear the work area of all parts and
debris that may cause injury by flying
objects. Securely fix the object to be
worked on in a vise or otherwise
clamp to avoid injury. Do not attempt
to hold workpiece by hand.
American
National
Standards
Institute (ANSI).
Inspect the tool before use. Run the tool
free of the workpiece before using to
ensure all parts are running smooth-
ly and there are no abnormal sounds
or sparks. If any defect is found,
have unit serviced.
Disassembly and improper reassem-
bly of this device can result in electri-
cal shock danger. Always have this
device serviced by a qualified electri-
cal repair technician. Serious injury
will result.
-13-
G9003 Portable Planer
-14-
G9003 Portable Planer
Ref. # Part #
Description
Ref. # Part #
Description
001 P9003001 Pan Hd Screw M4 x 16
002 P9003002 Chip Cover
029 P9003029 Brush Holder Cap
030 P9003030 Indication Plate
031 P9003031 Screw M5 x 10
032 P9003032 Compression Spring
033 P9003033 Rubber Packing
034 P9003034 Front Base
003 P9003003 Knob
004 P9003004 Scale Plate for Knob
005 P9003005 Flat Washer 10mm
006 P9003006 Main Frame
007 P9003007 Rivet
035 P9003035 Pan Hd Screw M5 x 18
036 P9003036 Base
008 P9003008 Name Plate
009 P9003009 Cord Guard
037 P9003037 Rubber Pin
010 P9003010 Cord
038 P9003038 Bearing (608ZZ)
039 P9003039 Drum
011 P9003011 Strain Relief
012 P9003012 Pan Hd Screw M4 x 18
013 P9003013 Noise Suppressor
014 P9003014 Switch
040 P9003040 Rubber Pin
041 P9003041 Hex Hd Bolt M4 x 20
042 P9003042 Bracket
015 P9003015 Handle Cover
016 P9003016 Pan Hd Screw M4 x 25
017 P9003017 Bearing (6000LL8)
018 P9003018 Stop Ring E-9
019 P9003019 Fan
043 P9003043 Pan Hd Screw M4 x 20
044 P9003044 V-Pulley 4-20L
045 P9003045 Belt Cover
046 P9003046 Rubber Pin
047 P9003047 Pan Hd Screw M4 x 25
048 P9003048 Poly V-Belt 4-24L
049 P9003049 V-Pulley 4-37
050 P9003050 Bearing (6000ZZ)
051 P9003051 Ruber Pin
020 P9003020 Armature Assy (w/17&22)
021 P9003021 Insulation Washer
022 P9003022 Bearing (627LB)
023 P9003023 Field Assembly
024 P9003024 Pan Hd Screw M4 x 16
025 P9003025 Auxiliary Baffle Plate
026 P9003026 Pan Hd Screw M4 x 10
027 P9003027 Bearing Cover
028 P9003028 Carbon Brush
052 P9003052 Adjustment Plate
053 P9003053 Pan Hd Screw M4 x 5
054 P9003054 Drum Plate
055 P9003055 Hex Hd Flange Bolt M6 x 17
G9004 Portable Planer
-15-
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
1. Low voltage.
CORRECTIVE ACTION
Motor will not start.
1. Check power line for
proper voltage.
2. Brushes worn or sticking.
2. Replace both brushes.
3. Open circuit in motor or loose 3. Inspect by qualified
connections. electrical technician.
Motor will not start; 1. Short circuit in line cord or 1. Inspect cord or plug for
fuses or circuit breakers
blow.
plug.
damaged
and shorted wires.
2. Short circuit in motor or loose 2. Inspect by qualified
insulation
connections.
electrical technician.
Motor overheats.
1. Motor overloaded.
1. Reduce load on motor.
2. Air circulation through the 2. Clean out motor vents
motor restricted.
Motor arcing visibly 1. Brushes sticking.
through vents or runs
erratically.
1. Check that brush hold-
er is free of dirt and
that brush moves
freely.
2. Brushes worn.
2. Replace both brushes.
Machine slows when 1. Feed rate too high.
1. Feed planer slower.
2. Reduce depth of cut.
3. Replace both brushes.
operating.
2. Depth of cut too great.
3. Brushes worn.
Machine is loud when 1. Excessive depth of cut.
cutting. Overheats or 2. Blades are dull
bogs down in the cut.
1. Decrease depth of cut.
2. Sharpen blades.
3. Blade holder or blade assem- 3. Recheck
complete
blade installation and
tighten all screws.
bly mounting is loose.
4. Belt is worn or loose.
5. Short circuit in motor.
4. Replace belt.
5. Inspect by qualified
electrical technician.
Planer starts, but cutter- Worn or broken belt
head does not move.
Replace belt
Planer starts, cutter- 1. Blade not extending below 1. Increase depth of cut.
head turns, no cut.
Rough or fuzzy cut.
foot.
2. Belt worn or slipping.
2. Replace belt.
1. Blades are dull.
1. Sharpen blades.
2. Excessive depth of cut.
2. Decrease depth of cut.
3. Cutting against natural wood 3. Reverse cutting direc-
grain. tion.
4. High wood moisture content. 4. Dry wood.
Cut not smooth or straight. Blade not flush with rear foot.
-16-
Reset blades in jig.
G9003 Portable Planer
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
MODEL # G9003 Portable Planer__
Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
___12" Table Saw
___12" Jointer
___Radial Arm Saw
___Panel Saw
___Lumber
___Brass Hardware
4. How long have you been a woodworker?
___Paint & Finishing Supplies
___Contractor’s Supplies
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Combination Planer/Jointer
___Other_________________________________
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
12. What new accessories would you like Grizzly
Industrial to carry?
6. What stationary woodworking tools do you own?
Check all that apply.
___Builders Hardware
___Fasteners
___Hand Tools
___Air Compressor
___Band Saw
___Panel Saw
___Planer
___Wood Components
___Other_________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
14. Do you think your purchase represents good value?
___Other______________________________
___Yes
___No
7. How many of your woodworking machines are
Grizzly? _____________
15. Would you recommend Grizzly to a friend?
___Yes ___No
8. Which benchtop tools do you own? Check all
that apply.
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___Yes
___No
___8" Table Saw
___Scroll Saw
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___8" - 10" Bandsaw
___Disc/Belt Sander
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___Other______________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
NOTES
-19-
G9003 Portable Planer
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number’’, which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon.
-20-
G9003 Portable Planer
|