Grizzly Grinder T10024 User Manual

MODEL T10024  
ACCESSORY KIT #2  
FOR T10010/T10097  
WET GRINDER  
INSTRUCTION SHEET  
Inventory (Figure 2)  
Introduction  
A. universal sharpening Jig ........................... 1  
b. Jig holder ................................................... 1  
C. universal sharpening Jig Knobs................ 2  
D. Chisel Jig.................................................... 1  
E. stone dresser ............................................ 1  
the model t10024 accessory Kit #2 for the model  
t10010/t10097 Wet grinder helps sharpen chis-  
els and dress grinding wheels.  
b
a
d
C
e
Figure 2. inventory.  
Figure 1. t10024 accessory Kit.  
Unpacking  
the model t10024 accessory Kit was carefully  
packed when it left our warehouse. if you discover  
any parts are damaged after you have signed  
for delivery, please immediately call Customer  
Service at (570) 546-9663 for advice. save the  
containers and all packing materials for possible  
inspection by the carrier or its agent. Otherwise,  
filing a freight claim can be difficult. When you  
are completely satisfied with the condition of your  
shipment, you should inventory the contents.  
Adhere to all safety warnings outlined in  
the Model T10010/T10097 Wet Grinder user  
manual. If you are not familiar with the prop-  
er usage of the Model T10010/T10097 Wet  
Grinder, review the procedures and safety  
warnings covered in that manual. Failure to  
do so could result in damage to the machine  
or personal injury.  
Copyright © November, 2007 by grizzly iNdustrial, iNC. revised may, 2011 (Jb)  
WARNING: NO pORTION OF THIS MANUAL MAY bE REpRODUCED IN ANY SHApE  
OR FORM WITHOUT THE WRITTEN AppROvAL OF GRIzzLY INDUSTRIAL, INC.  
(For models maNuFaCtured siNCe 11/07) #Jb10089 priNted iN ChiNa  
 
the chisel sharpening jig is capable of accurately  
sharpening a variety of chisels. the jig must be  
assembled and used differently depending on the  
tool you are sharpening and the way you want it  
to be sharpened.  
3. Clamp the chisel (bevel-side down) into the  
jig using the knob, as shown in Figure 7.  
your exact clamping method may vary slightly  
depending on your chisel.  
To assemble the jig for beveled chisels:  
1. Completely disassemble the chisel sharpen-  
ing jig as shown in Figure 5.  
Figure 7. Clamping bevel chisel (2-sided bevel).  
4. place the assembled jig onto the universal  
support, as shown in Figure 8.  
Figure 5. Jig disassembled.  
2. reassemble the jig and the jig holder as  
shown in Figure 6.  
Jig holder  
Figure 8. grinding beveled chisels.  
5. adjust the grinding angle by sliding the uni-  
versal support in or out and by repositioning  
the chisel in the jig. once the desired angle is  
achieved, tilt the chisel away from the grinding  
wheel, then connect the grinder to power and  
turn it ON.  
Chisel sharpening Jig  
Figure 6. beveled chisel jig assembled.  
To sharpen beveled chisels:  
6. return the chisel onto the surface of the  
wheel. use a firm grip on the chisel, but do not  
use heavy pressure against the wheel. move  
the chisel back and forth across the surface of  
the wheel while grinding to prevent excessive  
or uneven wheel wear.  
1. disCoNNeCt griNder From poWer!  
2. place the universal support in either the verti-  
cal or horizontal mounts, depending on the  
desired grinding action as described in the  
model t10010/t10097 owner's manual.  
-3-  
t10024 Wet grinder accessory Kit #2  
 
To assemble the jig for hollow chisels:  
Chisel  
Clamp  
Chisel  
pin  
1. Completely disassemble the chisel sharpen-  
ing jig as shown in Figure 5.  
2. re-assemble the jig as shown in Figure 9.  
Narrow Chisels  
Wide Chisels  
Figure 10. Clamping hollow chisels.  
4. place the assembled jig onto the universal  
support, as shown in Figure 11.  
Chisel sharpening Jig  
Figure 9. hollow chisel jig assembly.  
To sharpen hollow chisels:  
1. disCoNNeCt griNder From poWer!  
2. place the universal support in either the verti-  
cal or horizontal mounts, depending on the  
desired grinding action as described in the  
model t10010/t10097 owner's manual.  
Figure 11. grinding hollow chisels.  
3. Clamp the chisel (bevel-side down) into the  
jig, as shown in Figure 10. No single clamp-  
ing method works best for all chisels and only  
trial-and-error with each specific tool will give  
the best clamping orientation.  
5. adjust the grinding angle by sliding the uni-  
versal support and repositioning the chisel in  
the jig. once the desired angle is achieved, lift  
the chisel away from the grinding wheel, then  
connect the grinder to power and turn it ON.  
Tip: For narrow chisels, use the chisel pin to  
secure the chisel, as shown in Figure 10.  
6. return the chisel onto the surface of the  
wheel. use a firm grip on the chisel, but do not  
use heavy pressure against the wheel. rotate  
the chisel to grind the entire edge.  
-4-  
t10024 Wet grinder accessory Kit #2  
 
T10024 parts breakdown and List  
2
5
1
14  
13  
3
7
12  
1
4
6
8
9
11  
10  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
2
3
4
5
6
7
PT10024001  
PT10024002  
KNOB M6-1 X 20  
UNIVERSAL JIG  
KNOB M8-1.25 X 40  
CHISEL CLAMP  
KNOB BOLT M6-1 X 16  
CHISEL BED  
8
PT10024008  
JIG HOLDER  
9
PFH38M  
FLAT HD SCR M6-1 X 16  
PHLP HD SCR M8-1.25 X 10  
STONE DRESSER  
PT10024003  
PT10024004  
PT10010010  
PT10024006  
PT10024007  
10  
11  
12  
13  
14  
PS39M  
PT10024011  
PT10024012  
PT10024013  
PN01M  
CHISEL PIN  
THREADED SLEEVE M12-1.75 X 45  
HEX NUT M6-1  
CHISEL JIG  
 
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!  
~Since 1983~  
Visit Our Website Today For  
Current Specials!  
ORDER  
24 HOURS A DAY!  
1-800-523-4777  
 

Graco Welder 235627 User Manual
Greenheck Fan Fan MSCF BI User Manual
Grundig Flat Panel Television 46 VLE 7139 BR User Manual
Grundig Flat Panel Television GULCD32HDT User Manual
Hamilton Beach Coffeemaker 47451 User Manual
Hamilton Beach Fryer 35200 User Manual
Hasselblad Camera Lens HC 32 150N User Manual
HP Hewlett Packard Cell Phone Accessories E6380 90019 User Manual
HP Hewlett Packard Network Hardware 4400 User Manual
Husqvarna Lawn Mower Accessory H346SL User Manual