Grizzly Dust Collector T25448 User Manual

MODEL T25448/T25449  
DUST COLLECTOR  
REMOTE SWITCH  
INSTRUCTIONS  
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]  
Introduction  
The Model T25448/T25449 Dust Collector  
Remote Switch (Figure 1) allows you to remotely  
turn a dust collector ON/OFF from a distance of  
up to 75 feet.  
To ensure safe operation:  
• Only connect the switch box to power sup-  
ply that meets the listed specifications.  
• Do not connect the switch box to a dust  
collector with a motor that exceeds the  
listed specifications.  
Read and understand this entire document before  
installation to make sure this switch box fits the  
intended application.  
Switch  
box  
• This remote switch is ONLY designed to  
be used on dust collectors with standard  
ON/OFF toggle or push-button switches—  
not with magnetic switches.  
• If you are unsure about the type of dust  
collector switch you have, contact the dust  
collector manufacturer for more informa-  
tion.  
Remote  
Controller  
• Using this switch box for applications  
other than dust collectors may cause the  
unit to fail and will void the warranty.  
Figure 1. Model T25448/T25449 remote switch  
components.  
Specifications  
Model T25448:  
Replacement remote controllers (Model  
T25507) can be purchased by contacting  
Grizzly at (800) 523-4777. Before the new  
remote controller can be used, the switch  
box must be programmed to work with it  
(refer to Programming Switch Box on Page  
2 for detailed instructions).  
Power Supply ....................120V, 15a, 60 Hz  
Outlet Type .................................NeMa 5-15  
Max. Dust Collector HP..................... 1.5 HP  
Model T25449:  
Power Supply ................... 240V, 20a, 60 Hz  
Outlet Type .................................NeMa 6-20  
Max. Dust Collector HP........................ 3 HP  
Remote battery ..........................Type 23ae, 12V  
Communication Type........Radio Frequency (RF)  
Max. Communication Distance ................... 75 ft.  
COPYRIGHT © FebRuaRY, 2013 bY GRIZZLY INDuSTRIaL, INC.  
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
FOR MODeLS MaNuFaCTuReD SINCe 8/13 #TS15583 PRINTeD IN TaIwaN  
 
4. Press either button on the remote controller  
(see Figure 5)—you will hear three beeps  
and the red receiving light on the switch box  
will flash three times.  
Operation  
1. Make sure the switch box is properly installed  
and correctly programmed with the remote  
controller.  
2. Turn the dust collector ON/OFF switch to ON.  
Sliding  
Cover  
ON button  
3. Press the remote controller ON button once  
to turn the dust collector ON. The green  
power light on the switch box will also illumi-  
nate (see Figure 6).  
OFF button  
Figure 5. Remote controller buttons.  
Green  
Power  
Light  
5. wait approximately five seconds and you will  
hear another beep—the switch box is now  
programmed to work with this remote control-  
ler.  
Figure 6. Green power light on switch box.  
4. Press the remote controller OFF button once  
to turn the dust collector OFF. The green  
power light on the switch box will turn OFF.  
Un-programming Switch Box  
If necessary, the switch box can be un-pro-  
grammed so that it will not operate with any  
remote controller. In such case, you will have  
to re-program the switch box to operate with a  
remote controller.  
To un-program the switch box:  
1. Press and hold the black programming but-  
ton on the switch box for approximately five  
seconds—you will hear one long beep and  
the red receiving light will flash once.  
2. The switch box is now un-programmed.  
-3-  
Model T25448/T25449 (Mfg. Since 8/13)  
 
Troubleshooting  
Review the troubleshooting and procedures in this subsection if a problem develops. If you need additional  
help with a procedure, call our Technical Support at (570) 546-9663.  
Note: Please gather the serial number and manufacture date of your switch before calling.  
Symptom  
Possible Cause  
Possible Solution  
Switch box will not  
turn ON.  
1. Switch box not connected to power.  
1. Connect switch box to correct power source (Page 2).  
2. Remote controller not properly programmed 2. Properly program remote controller to operate switch  
to operate switch.  
(Page 2).  
3. Remote controller battery weak/dead.  
4. Switch box circuit breaker has tripped.  
3. Replace remote controller battery (this page).  
4. Press the circuit breaker reset button on rear of  
switch.  
5. Remote controller is out of range with 5. Operate the remote controller within 75 ft. of the  
switch.  
switch.  
6. wall circuit breaker has tripped.  
6. Reset wall circuit breaker. Make sure breaker is in  
good condition and circuit is properly sized for dust  
collector in use.  
7. Remote controller/switch at fault.  
7. Test/replace.  
Dust collector will  
not turn ON.  
1. Dust collector ON/OFF switch not turned 1. Turn dust collector ON/OFF switch ON.  
ON.  
2. Dust collector not connected to switch box. 2. Properly connect dust collector to switch box  
(Page 2).  
3. Switch box not connected to power.  
4. wall circuit breaker has tripped.  
3. Connect switch box to correct power source (Page 2).  
4. Reset wall circuit breaker. Make sure breaker is in  
good condition and circuit is properly sized for dust  
collector in use.  
5. Dust collector at fault.  
5. Refer to dust collector manual for troubleshooting;  
contact dust collector manufacturer for technical  
help.  
Replacing Remote Controller Battery  
The remote controller is independently powered  
by a Type 23ae, 12V internal battery. If the switch  
box stops responding to the remote controller,  
replace the battery as the first course of resolu-  
tion.  
To replace the remote controller battery:  
1. Place the remote controller upside down on a  
stable, protective surface.  
Figure 7. Remote controller components.  
2. use a #00 Phillips screwdriver to remove the  
three screws that secure the components  
together.  
4. Replace the battery, then re-assemble the  
remote controller.  
3. Carefully separate the covers, circuit board,  
and battery, as shown in Figure 7.  
-4-  
Model T25448/T25449 (Mfg. Since 8/13)  
 

Grizzly Biscuit Joiner G0490 User Manual
Grizzly Impact Driver G5789 User Manual
Grizzly Lathe H8259 User Manual
Grundig Hot Beverage Maker WK 4062 User Manual
Hans Grohe Plumbing Product 32111001 User Manual
Hasselblad Scanner Flextight X1 User Manual
Heath Zenith Work Light 598 1283 00 User Manual
Hubbell Switch LXi 2300 User Manual
Humax Satellite TV System CI 5100 User Manual
Hypertec Carrying Case TSV12V1HY User Manual